Hello! This is Hwang Bank.
This time, we review the Galaxy Gallaz computer case among IT products.
Galaxy is famous as a graphics card brand, but there is GALAX Galaxy. As a gaming gear, EX series keyboard mouse headset is also famous!
This time, we released a PC case.
The case I am reviewing is the product Galaxy GALAX EX-01 ARGB Mesh Tempered Glass (Black)!
A white case is also released, and the white case is a mixture of BLACK and WHITE colors, so you can configure the system in two colors.
The EX-01 has a tempered glass swing door, and is a case that has a good tuning effect and reflects the latest trends by configuring 4 directional 120mm RGB cooling fans instead of regular fixed RGB fans.
There is an On/Off FAN LED power button and an LED effect change control button on the front top I/O interface.
It has an integrated fan controller, so it can be controlled by the motherboard’s software by connecting the motherboard’s PWM signal and ARGB signal to the controller.
Galaxy Tempered Glass GALAX EX-01 ARGB Mesh (Black)
Galaxy Tempered Glass GALAX EX-01 ARGB Mesh (Black)
Looking at the size and weight of the case, width (W) depth 215mm (D) height 424mm (H) 460mm, it’s big and heavy at 5.8kg!
There are a total of 7 PCI slots.
The PC case stand sits firmly and the pad is attached!
It’s a mid-tower case that has scalability, compatibility, and convenience in a luxurious design.
Components are slightly different from common cases and provide additional components.
case manual, hub connection manual, Cable ties, various screws, Graphics card support, ARGB interlocking cable
The graphics card support can be adjusted in all directions, up and down, front and back, left and right.
The front has a diagonal mesh bezel design, so if you hold the panel release handle at the bottom and immediately pull it out, the front panel can be easily removed for easy cleaning.
The front has three 120mm ARGB fans.
I/O Power, Reset, LED Brightness, LED Mode, MIC and HD Audio, USB 2.0 Type-A x 1, USB 3.2 Gen1 Type-A x 1
There is a power button on / off 5 FAN LED steps and 18 LED effect change control buttons, and there is an integrated fan controller, so if you connect the PWM signal and ARGB signal of the motherboard to the controller, integrated control is possible with the motherboard software.
I like it because I can control the water cooler too!!
The front panel is a mesh filter panel and no dust filter is provided inside. The panels are easy to move and easy to clean.
The upper part has a magnet-type dust filter, and the sub-type power booth has a film-type clasp-type mesh filter that can be attached and separated.
In fact, since the lower part collects more dust than the upper part, it would have been better if it was a slide type or a magnet type because it is easy to clean! haha
The main left panel has a swing door tempered glass as per the latest trend. It even comes with a protective film!
It also has a high quality metal covered handle that makes it easy to open and close, which makes it very easy to manage the interior.
The tempered glass door is fixed with a magnet and can be separated in the form of a hinge.
The opposite right hand chassis can be opened with thumb screws and is made of sheet steel panels.
Now let’s look inside!
Installable mid-tower case for ATX / Micro-ATX / Mini-ITX motherboard.
The CPU cooler is up to 170mm, so it is possible to install a normal tower type air cooler,
The VGA graphics card is 340mm, which is enough even with the 3060 ti 3 fans I use.
It is a case that users who like cost performance will like it.
The CPU power cable can be connected while the motherboard is installed.
The line arrangement space is about 22 mm, and when you assemble it, the line arrangement is relaxed.
The front liquid cooler space is also measured at 33mm!
A cable clip is attached to help organize common cables except the main power cable. ^^
A main storage device bracket is provided in the power supply chamber to enable HDD & SSD installation, and two SSD brackets are added on the side for convenient installation of additional SSDs. A total of 4 storage devices can be configured. It is extensible enough for ordinary users.
The mounting part of the power supply is 180mm as standard, and the space next to it is up to 220mm. If you remove the hard disk bay, you can use it more widely, so the convenience of use stands out.
After arranging the wires, the space up to the top of the hard disk bay was wide, so it was very convenient to arrange unused wires.
Primary cooling is provided by three 120mm fans at the front and one 120mm fan at the rear.
Instead of fixed RGB, an ARGB fan with good tuning effect is provided as standard.
With the thought that it would have been nice if the front was 140mm, it’s a basic ARGB fan configuration, so it’s understandable given the cost performance. ^^
”120mm GALAX REVOLT-01 ARGB” 4 basic fans provided (3-pin fan connector, addressable 5V 3-pin RGB connector provided)
The EX-01 can have up to two 140mm cooling fans or a water cooler radiator with a maximum size of 240mm at the top.
The top of the power supply chamber is well drilled and provides screw holes for mounting two 120mm cooling fans.
If you install a 240mm liquid cooler on top of the case and two 120mm fans on top of the power cover, it seems to be the best cooling condition to use!
Cooling fan hub (HUB) provided as standard – 5 cooling fan headers and 5 addressable RGB headers
It has an integrated fan controller, so it can be controlled by the motherboard’s software by connecting the motherboard’s PWM signal and ARGB signal to the controller.
To supply power to the hub, connect the power supply SATA cable.
“finish”
Galaxy GALAX EX-01 ARGB tempered glass mesh BLACK (BLACK).
Reflecting the latest trend, the ‘120mm GALAX REVOLT-01 Addressable RGB’ 4 basic fans and fan boost are provided as standard, so the tuning effect is good.
If I had provided two more, I think … but even this much for the cost performance satisfies the sensible.
There are 5 cooling fan 3-pin headers and 5 ARGB 5V 3-pin headers, so the basic fan can be controlled by the case itself, and 18 LED control effects can be used by connecting to a hub even on a motherboard with only ARGB 12V 4-pins and no 5V 3-pins. This is possible.
When you actually use it, it must be a hit with the tuning effect provided by the basic ARGB fan! very pretty! ^^
Galaxy Tempered Glass GALAX EX-01 ARGB Mesh (Black)
PC Case (ATX) / Middle Tower / Power Not Included / Standard-ATX / Micro-ATX / Mini-ITX / Cooling Fan: Total 4 / LED Fan: 4 / Side: Tempered Glass / Back: 120mm LED x1 / Front: 120mm LED x3 / Width (W): 215mm / Depth (D): 424mm / Height(H): 460mm / Power Mount : 180mm / Power Location : Back Bottom / GPU Mount : 340mm / CPU Cooler Mount : 170mm / Fan Control / RGB Control / External LED Control / LED Color: ARGB
[구매링크]
https://prod.danawa.com/info/?pcode=15518525
#Computer Case #PC Case #Computer Case Recommendation #Galaxy #Galaxy #GALAX #EX-01 #MESH #ARGB #Mash Case #Mesh Case #Tempered Glass #Case #Black #White #120mm #FAN #Case Introduction #Review
